A Few More Things

 Eyebrow

For Brian's first attempt at fabricating a new eyebrow

he tried using the leftover .032" 2025-T3 

sheet of aluminum from the front panel.  

It was not the best aluminum to make the flexible brow.

He ordered some (softer) .032" 2024-0 aluminum from a local 

aircraft supply store.  When he went to pick up the order they

had a (thicker) .040" sheet of it instead.  

Even with the thicker metal it was so much easier to work with than the body panel aluminum.

2024-0 aluminum= nice eyebrow &  happy fabricator

Battery Box

When we bought our trailer there was no battery box; only a wooden shelf was attached to the front of the trailer.   Brian looked at pictures of old battery boxes for the inspiration to make ours.

support first

support frame & acid proof paint
We know what battery acid can do to aluminum.

   Our box is large enough to house two marine batteries.  

Smaller tractor batteries that would have been used originally.

Floor

We installed the VCT floor.  

We tried to come as close to the original floor as possible.  

The new tile is different from the old in two ways: 

It's 12x12 instead of 9x9 and is asbestos free!

Our inspiration piece:

 

a small section of our old floor

 

before

Square one.  The best place to start.

Ta-daa!  (Only 6 more coats of sealer and it will be finished!)

 

Goodbye, Decals

Back in February 2010 during the demo phase of our restoration we discovered some travel decals in our trailer.  We were delighted by the decals, feeling like our trailer was telling us part of its story.

Now, it's almost time to paint the interior skins.

Because I'm so sentimental about our decals I wanted to take our last opportunity to get the gang back together for a photo.

Ok, I confess.
I'm really "getting the gang back together" because I had a total hard drive failure in December. 
I couldn't stomach the thought of having zero pictures of the decals.
The cost for pictures?  Stripping the endcap after it was installed.
(Yikes!  Look out for falling stripper!!!)

We have a total of 61 decals. 
There are only 16 that we can't decipher.  

Here are the gratuitous close-ups with all the gory details:

Boy Scouts, unknown (2), Yellowstone

Mt. Rushmore, Black Hills S. Dakota

The Castle on Cedar Pass Badlands Monument South Dakota , 

South Dakota The Greatest Pheasant Area on Earth, 

Boy Scouts of America

Wisconsin, Minnesota, No. Dakota, Illinois

 

Iowa, Wyoming, Idaho, Oregon

 

Washington, Seattle 1962, Grand Coulee, (Canada), Banff Canada

 

Lake Louise Banff Pk Canada, unknown (2),
Tri-State Mich/Penn/Ohio, Michigan

Michigan, "Prevent Forest Fires," Ontario Canal, 

Arkansas, Key West, FL, unknown

unknown, New Mexico,  Painted Desert Arizona,

Sequoia National Park, Kings Canyon California, Golden Gate Bridge

San Francisco Chinatown, Hawaii, Kauai, Maui,

Grand Tetons NP Wyoming, Jackson Hole

Tampico Mexico, Vera Cruz

Any guesses?  The second one says '68.

 Around the door:

unknown, Maine

Indiana, unknown

(2) unknown, Laborers Local 534

unknown, Canada, unknown

When I stripped the paint off of the decals we were delighted to figure out 3 decals we couldn't previously decoded:  the first Boy Scouts decal, Key West, FL, and Maui

It was sad to see them go:

see the paint bubble

Goodbye, decals.
Someday I hope that all of us will have an extensive travel portfolio like our trailer.

The Best Part

We have all worked hard to install the skins:

Sabrina stole Daddy's tool belt in hopes that we would put her to work.

Samuel popping rivets in the bathroom

Annabelle is a two fisted helper... pop riveter and cleco pliers.

There are still two skin panels not fully installed.  The front panel was left open for battery installation and a little wiring.  A section of the long ceiling panel is still uninstalled so that we can add the eyebrow for the

 front door.  

Hey look!  What's that I see?  I think it's an aluminum tent!

Time for a reward for all of that work... our first trip!

Hitched up and heading to Fort Yargo State Park, Georgia.

The best part about camping... being with friends!

Nose Job

We have an ugly front panel.
  

 Very ugly.

Notice the line of corrosion in the middle of the panel.  Apparently battery leaks do bad things to aluminum.

As bad as this panel looks, it used to look worse.  In order to get it lookin' this perty we polished and polished and polished.  We patched holes...

 We considered making an extra large battery box to cover most of the panel.  

We banged out dents.

We still weren't satisfied.

On Monday, we decided that this panel "just won't do."  Fortunately, there's a company just south of Atlanta that stocks 2024 aluminum.  The kids and I drove an hour to Peachtree City, Ga to pick up some aluminum for the panel.

 

Time to take out the panel

This panel wasn't doing such a great job of protecting the aluminum under it.

 Brian used the removed panel as a pattern for the new one.

 It was dark by the time we finished bucking the rivets.

Much better!

We had talked about changing this panel lots of times... if only we had known how simple and inexpensive this project was, we would have done it earlier.
  

Stripping/Showing a Little Skin

We're stripping paint, putting the skins in, cutting holes for new outlets...

 

This is our ceiling.  On the floor.  

We've been working around/walking around this huge ceiling roll forever.

 We decided to take it out and strip it (again) before installing it.

Stripping isn't fun.

 It's much easier to do with horizontal panels though.

I'll spare you the picture of the inside of that 5 gallon bucket.  It's where I put all of the paint and stripper goo after I scraped it off... we call it the "puke bucket."

Warning!  Gratuitous side note:

Buying the stripper was fun. 

The cashier at the home store told us:
"You have to be 18 to buy a [can of] stripper."  Haha!

(She wasn't kidding though, it's the law in GA.)

Brian installing the lower curbside skin.  

Our headlamps are very useful in late-night Airstream restoration as well as camping.

We're so excited about working on the skins.

We're adding a total of 7 new outlets to our trailer.  For each new outlet, we have to make a cut in the skin.  So, the skin installation is taking a little bit of time but we're getting close.

Ends Capped

Here's what we've been working on since our last post:

Installed two inside fiberglass endcaps

cleaned the endcaps

more wiring

sealed some leaks (every Airstream owner's favorite task)

sealed some more leaks

made the frame for the new battery box

worked on a new drip cap for the front door

washed the trailer (first bath in a year, YIKES!)

Did I mention we installed the fiberglass endcaps?! We used 3 "third hands" and a farm jack to complete the job.  Stubborn things!  We were so glad to finally be successful at this task. 

Lost in Translation

(from Brian)

My (overly-ambitious) wiring plans drag on, but the end is in sight.  All of the 110v wiring is done.  Check.  Now to finish the trailer lights.

When we purchased the trailer, the trailer lights (taillights, brake lights, turn signals) had been completely bypassed.  Temporary wires dangled under the belly pan and up the outside of the tail.  Not the least, the trailer brake wires were completely cut off.  This arrangement (sans trailer brakes) worked for almost the whole ride home before it blew a fuse in our tow vehicle.

flashback: our wiring looks so classy taped to the rear of the trailer and wrapped around part of the bumper

We had a bit of a snafu the first time I rewired the trailer lights.  The night before we moved out of our warehouse, we hooked up the tow vehicle and...nothing.  Since it was time to move out, I grabbed a 4-wire connector and ran some quick temp wires to the lights.  Once we were back home, I tested and found out that 4 of the wires on the molded Hopkins 7-blade cable I purchased didn't have continuity.  I assumed that I must have damaged it in some way during installation.

Months later, I finally got around to replacing the wiring pigtail.  I went back to the same store and bought another pre-wired Hopkins 7-blade connector.  I spliced it in, hooked up the tow vehicle, and... uh-oh.

The brake lights didn't work at all.  No left blinker.  The right blinker made the running lights on the left side of the trailer blink.  Crap.

I began to doubt my sanity and worth as a human.  Frustration rose.  Then, I began tracing down the wiring.

Turns out the color-coded wiring I bought is very different from what I expected.  On a 7-blade connector, the usual scheme that Hopkins uses for color-coding the wires is in this order, clockwise from top: brown, yellow, white, blue, green, black, with purple/red in the middle.  What I got from my pre-wired (Hopkins) connector was oh-so-different: green, red, white, blue, brown, black, with yellow in the middle.  Wow!  I really wish I had found the chart on this page to start with; I would have known that they used a completely different color-coding scheme.  It'd be nice if Hopkins would note that on their website.

It was an easy enough fix to swap the wires around and apply some colored electrical tape to avoid future confusion.  Woo-hoo!  The wiring checklist grows shorter...